Pharmaceutical & Biotechnology Manufacturing
Clean welds for pharmaceutical
& biotech equipment.
Practical weld cleaning and finishing for equipment builders working on stainless vessels, process pipework and production skids. Bring us the weld and the finish you need.

01 Vessels, pipework & skids
02 Surface finish & final cleanup
03 Equipment & part identification
The challenge
The finish is part
of the job.
A useful finishing process fits the part, the surface and the way your team works.
01 / HEAT TINT
Finish the weld zone
Treat discolouration on accessible stainless seams without making unnecessary abrasive blending the default. Include branches, fittings and the inside faces you need to reach.
02 / CLEANUP
Plan the final surface
Product-contact areas, external supports and outer housings do different jobs. Define the finish and cleanup for each, including joints that can hold process fluid.
03 / REPEATABILITY
Make the process repeatable
Bring the same surface requirement through fabrication, outsourced parts and later modifications. Match preparation, cleaning and inspection to the work order.
See the cleaning result
Heat tint removed.
A visible difference.
One stainless weld, three stages: before cleaning, partly treated and after ProPlus cleaning.

Stainless weld-cleaning demonstration. Check the finish and final cleanup on a representative component from your equipment project.
Typical fabrication applications
Built around the parts
you need to finish.
Choose the treatment around the weld, the access and the finished surfaceβnot just the machine rating.

VESSELS
Tanks & mixers
Clean accessible vessel seams and local weld zones. Plan treatment before access is restricted by fittings or final assembly.

PIPEWORK
Pipework & manifolds
Work around tube joints, bends and branches. Check brush reach and final cleanup on representative fittings.

FABRICATION
Skids, frames & guards
Give external stainless structures and equipment housings a consistent finish alongside the process equipment they support.

IDENTIFICATION
Equipment IDs & tooling
Consider serial numbers, asset IDs and identification of removable parts. Agree the mark location, readability and service conditions.

A practical workflow
Build the finishing step
into the fabrication plan.
01
Define the surfaces
Identify the alloy, required finish and which weld faces contact the product. Bring any specified treatment or acceptance check into the job plan.
02
Clean while access is good
Choose a compatible machine, fluid and brush. Try the difficult fitting or corner before committing to the production sequence.
03
Complete cleanup and inspection
Follow the product instructions for residue removal. Inspect the dry surface and carry out the checks specified for the equipment.
Equipment to evaluate
Match the machine
to the work.
Use a representative sample to compare the finish, complete cycle and working setup.

SMALLER TIG WORK
Power30
A starting point for controlled TIG cleaning on smaller components and accessible tube work. Check the brush reach and finish on your own sample.

REGULAR STAINLESS FABRICATION
ProPlus
For regular stainless TIG and suitable MIG cleaning on assemblies, fittings and fabricated equipment. Consider the complete cycle and handling around the part.

HEAVIER CLEANING WORKLOADS
FURY100
Compare FURY100 where longer seams, heavier oxide or daily cleaning volume justify more capacity. Demonstrate the setup on a representative vessel or weld.
Start with the weld and workload.
Tell us the material, deposits and daily volume. Check the electrical supply and equipment variant for your location.
Practical process decisions
The right finish starts
with the right brief.
A successful demonstration answers the equipment builderβs production questions. It should also leave the responsible quality team with a clear view of the finished surface.
Material, finish & access
Identify the stainless grade, thickness and existing finish. Include internal faces and restricted access. Start with the electrochemical weld-cleaning guide for the workshop sequence.
Cleaning and passivation
Removing visible heat tint and completing a specified passivation process are different requirements. Agree the treatment and checks needed for the actual equipment. See passivation after welding.
Fluid choice and residue removal
Match the exact fluid to the machine and surface. Plan wiping, rinsing and neutralization from the current instructions, including areas that trap liquid. Compare cleaning fluids and pickling paste.
Practical questions
Bring the right questions
to the demonstration.
Which welds should we bring to a demonstration?
Bring the welds that take the most finishing time: a typical seam, a darker area, a branch connection and an awkward corner. Include the finish requirement and any specified acceptance check.
Can we evaluate the process on product-contact equipment?
Yesβdiscuss the actual part and surface requirement with the equipment owner. Define the treatment, final cleanup and inspection for that application. A general cleaning demonstration does not qualify an entire pharmaceutical process.
How should equipment and removable parts be marked?
Choose the location and method around the material, cleaning regime and readability required in service. Consider MK310 laser marking or MK612 electrochemical marking, then compare samples using the marking and traceability guide.
Put your application to the test
Show us the equipment.
Letβs plan the finish.
Send a weld photograph, a drawing or a sample. Weβll help identify a useful Cougartron demonstration for the surfaces, access and workload in your project.
What to include
The equipment
Vessel, pipe assembly, skid or removable component
The surfaces
Alloy, weld process, finish and product-contact areas
The work
Access, cleaning volume and required final checks
